Warman Slurry Pump - Gland Seal Assembly

2020-04-17 09:47:16 Source: sand dredge pump-slurry pump parts-China Do Pump
Share to:

News Digest:Warman Slurry Pump - Gland Seal Assembly, china slurry pump, warman slurry pump, slurry pump parts

Warman Slurry Pump - Gland Seal Assembly 

How to assemble gland seal of Warman slurry pump, here is an article written by China Do Pump, a Warman Slurry Pump Solution provider, including Warman Slurry Pump - gland Seal Assembly, Warman Slurry Pump Parts - Bearing assembly test instructions, How to Maintain warman slurry pump - Bearing lubrication, How to Maintain warman slurry pump - Adjust slurry pump impeller, how to maintain warman slurry pump shaft seal?, What are the steps when Warman slurry pump stops?, What are the Reasons cause warman slurry pump operate failure? , What are the inspections before Warman Slurry Pump starts, what are the features of warman slurry pump, what are the type of warman slurry pump, how to select a warman slurry pump, for any question related to warman slurry pump, contact China Do Pump at [email protected] or call us at +8615031104888
china slurry pump
Packing component: Assemble packing box, packing pad and water seal ring, packing, shaft sleeve, positioning sleeve and shaft sleeve O-ring.

1. Place the stuffing box (Warman Slurry Pump Parts Code 078) on the table surface. (Filler side up)
2. Install the lantern restrictor (Warman Slurry Pump Parts Code 118) (small diameter downward) on the stuffing box stop.
In some applications, a neck ring (Warman Slurry Pump Parts Code 067) and a lantern ring (Warman Slurry Pump Parts Code 063) are used in place of the lantern restrictor (Warman Slurry Pump Parts Code 118).
3. Install the shaft sleeve (Warman Slurry Pump Parts Code 075), and one end slightly enters the inner hole of lantern restrictor (Warman Slurry Pump Parts Code 118).
4. Install packing ring (Warman Slurry Pump Parts Code 111), the ring must have the correct length, and the seams must be staggered from each other.
5. Assemble the split packing gland (Warman Slurry Pump Parts Code 044), screw in the gland clamp bolt (Warman Slurry Pump Parts Code 126) and tighten it, put the packing in the stuffing box, and push down, press the packing, insert the packing gland bolt (Warman Slurry Pump Parts Code 045), and tighten the nut properly, Seize the bushing.
6. Install the shaft O-ring (Warman Slurry Pump Parts Code 109) on the shaft and push it out of the labyrinth sleeve.
7. Put the assembled stuffing box into the pump body and gently tap with a small hammer to bring it into its proper position. Install the sealing water pipe on the top of the stuffing box, the shaft sleeve is likely to be forward, and it should be pushed back against the labyrinth sleeve and O-ring.
8. Assemble the second shaft O-ring (Warman Slurry Pump Parts Code 109) and push it into the groove on the end face of the sleeve.
9. Install the shaft spacer shaft O-ring (Warman Slurry Pump Parts Code 117) on the shaft and make it close to the shaft sleeve.
10. Apply a thin layer of lubricant to the shaft thread
warman slurry pump
China Do Pump is a manufacturer of slurry pump, sand pump. dredge pump, electric submersible sand pump and hydraulic submersible dredge pump with relative dredging equipment.For more warman slurry pump solutions related to Warman Slurry Pump - Gland Seal Assembly, contact Sand Pump Manufacturer China Do Pump at [email protected] or call us at +8615031104888.

Next:Warman Slurry Pump - How To Assemble Expeller Seal

Prev:Warman Slurry Pump - Bearing assemble to pump shaft ?

  • AddressXinhe Street, Xingtang Industrial Zone,Shijiazhuang, Hebei
  • Phone Number0086-15031104888
  • Email[email protected]

Dredge Pump For Sale|24/7 on line|China Do Pump Sitemap